Making Your Own Bamboo Fly Fishing Rod

Woodworker and fisherman Jeff Day decided to combine his two passions and create a useful and durable bamboo fly fishing rod.

I’ve been a woodworker and a fly fisherman for years, so it was probably inevitable that sooner or later I would build a bamboo fly rod. Inevitable, perhaps, but not necessarily a walk in the park. It cost me a fishing season. I broke rods long before they left the shop. I made rods that worked better as tomato stakes. I fried one rod to a crisp. I suffered epoxy failures and polyurethane busts. In short, I enjoyed every minute of it and, three rods after I started, I have a rod that I’m not ashamed to show to the world.

To start with, the author ground an edge into a bench chisel and used it to split the culm off the Tonkin bamboo cane in several segments.

A bamboo fly rod is made of six strips of bamboo glued together to form a hexagon. The strips are triangular in cross-section, and since the rod tapers from handle to tip, the triangular strips taper, too — the triangle is bigger at one end of the strip than the other.

All of this is done in three stages: First, you rough out a rod blank, splitting the bamboo stem to stern, kiln-drying it, and then planing it into long triangular strips — a set of six strips for each section of the rod. In the second stage, you taper the triangular strips with a block plane and a special metal form. Then you apply glue to the pieces and clamp them together by wrapping them tightly with thread. On a good day, it’s a piece of cake. On a bad day, it’s worse than getting skunked on the stream. Far worse. The final stage is applying the finish and attaching the hardware. I like to think of the stages as lumberjack, cabinetmaker and finisher.

Stage One: Lumberjack

This stage begins with a piece of Tonkin cane, the only cane used in rod making, because its long, dense, fibers make for a powerful rod. In the entire world, Tonkin cane grows in a single 30-square-mile patch of China.

Technically, bamboo is a grass, and a stick is called a culm. The easiest and fastest way to get the strips you need is to split the culm the way Windsor chair makers rive a chair back from a log, and for the same reason. Splitting bamboo gives you a piece with long parallel strands of grain. Rodmakers often make their own splitters that they drive into the end of the culm. Mine are chisels with edges that are ground to a rounded point. As the pieces get smaller, I hold the end of the chisel on the bench with one hand, and feed the bamboo into it with the other. The goal: six strips plus whatever else you can get from the bottom five feet of the culm. This will be the butt section. The tip comes from the upper five feet of the culm, and because rods traditionally have an extra tip, you’ll want to split it into 12 pieces.

Bamboo tends to curl easily in the presence of heat , so to give it a nice fishing pole curve and remove any nodes, run it over a heat gun.

At this point, a couple of minor adjustments are required. A stick of bamboo is divided into shorter sections by a series of bumps, called nodes. You need to get rid of them and deal with the bends that typically occur around them. Fortunately, bamboo bends when heated. Holding the node directly over a heat gun until the wood is almost too hot to handle makes the heated section bend like warm plastic. Once I’ve heated it, I can flatten the node completely (or almost so) by clamping it in the vise with the outside face against a jaw. I count to 10 as I clamp the edges between the jaws to straighten out the bends. If any of the nodal bumps remain, they’re sanded out by hand with 240-grit paper and a hard rubber sanding block.

A simple planing jig and a benchtop planer will help get your strips cut down into the triangular pieces you will glue up to make the rod.

Before shaping each piece into a triangle, there are two more steps. The first is to get each piece down to a manageable width. Traditionally this is done with a hand plane — it may be a grass, but bamboo works like wood. Tradition has its place, but this isn’t really the time for it. I rip the strips to width on the table saw (use lots of featherboards), and then I plane them into triangles on a jig in the planer. The planer jig is a simple oak auxiliary table with 60° grooves routed into it. Battens on the bottom fit snugly against the front and back of the planer bed to hold the jig in place.

As you go through the planing process, check each piece regularly for thickness, you need to ensure the accuracy of each piece you cut before moving on.

Each groove is slightly shallower than its neighbor — the largest is about 3/8" deep and the smallest is about 1/16" deep. I feed all the strips into the first groove, flip them edge for edge, and then feed them into the next shallower groove. I slowly work my way down the table until I’ve planed the strips to the exact size required by the rod.

To kiln dry the long bamboo pieces, the author rigged up a simple kiln with the heat gun and a duct system long enough to fit the bamboo.

Like any piece of lumber, your strips of bamboo need to be kiln-dried. This not only drives out water that might haunt you down the road, it tempers the bamboo, turning what would otherwise be a soft rod into one with backbone. It doesn’t take long — about 10 minutes at 350 degrees for the butts, and slightly less for the tips. I use a heat gun, combined with a couple of heat ducts — one inside the other — with lots of insulation around the outer pipe.

The heat gun shoots heat down the outside duct; it rises into the inner duct at an even temperature. I use two meat thermometers, one at the top and one at the bottom of the ducts, to monitor the temperature.

Stage Two: Cabinetmaker

Here, tradition rules, and I am fine with it. You are working with a finely tuned plane, a razor-sharp blade, and a tapering jig that adjusts to thousandths of an inch. I enjoy it the way I enjoy fly casting — nothing matters but what you’re doing, and what you’re doing is about as good as it gets.

The fact is that while there is no perfect taper for a rod, there are thousands of bad ones. I chose a time-tested taper developed by Everett Garrison. Garrison made some 700 rods from 1927 until his death in 1975, and they are considered some of the finest ever made. I copied the 7" rod he used on the last day he went fishing. Some of his other tapers, as well as his directions for building, can be found in his book A Master’s Guide to Building a Bamboo Fly Rod, coauthored with Hoagy Carmichael. Understanding how rodmaking works means understanding how the tapering jig works. The tapering jig, also called a planing form, is made of two bars of steel five feet long. The edges that face each other are chamfered and form a V-groove when the bars are put together. At one end of the jig, the chamfers form a deep valley; at the other end, they form a shallow valley. In between, the chamfer forms a valley that slopes evenly between the two ends. The bamboo sits proud of the jig, and you plane it until the plane is riding on the jig. When it is, the bamboo is the same shape as the valley — wide at one end, narrow at the other. Because of the hundreds of different rod tapers, you can adjust the depth of the valley every five inches using a pair of bolts. One bolt pushes the metal bars farther apart, the other pulls them together.

Setting the forms to the proper taper requires two tools from the machinist’s trade — the dial caliper and a depth indicator with a pointed tip. Initially, you set the forms with a depth gauge and, after planing a test strip, you check the setting’s accuracy with the dial caliper.

Gluing the Rod Together

When the strips are finished and laid out, glue them together with waterproof polyurethane glue and let it cure.

When the strips have been planed to final dimension, it is time to glue them together. Initially, I used polyurethane glue. It is widely available, affordable and waterproof. It fills gaps, has a working time of 20 to 30 minutes and dries the same color as bamboo. Unfortunately, 20 to 30 minutes isn’t a lot of time when you’re trying to clamp up six pieces of bamboo only slightly thicker than the butt end of a leader. The pieces slipped, slid and twisted as I worked, and to make a long story short, the polyurethane rods were the ones that became tomato stakes. I use industrial epoxy now, which is surprisingly friendly — it dries slowly, so if I have a problem I have hours to solve it.

Stage Three: Finisher

To best install the ferrule, file down the ends of the blank as it turns on your lathe, using a three- or four- jawed chuck to keep it from moving too much.

All that remains is putting the ferrules, handle, reel seat and line guides on. Ferrules first: The i.d. of the ferrule is less than the o.d. of the rod, so you file down the ends as the blank turns on the lathe. You’ll need a three- or four- jawed chuck and a support to keep the far end of the blank from whipping around. I made my support by bolting a piece of plywood to a table saw outfeed stand. Drill a hole in the plywood, line it with something soft (like a cork with a hole drilled in it), and then feed the rod through the hole to steady it. The handle and reel seat get glued on next — I suggest ready-made ones for your first rods; learn to make your own later.

To get the guide loops attached, tape one end down and use your fly-tying bobbin to start wrapping silk thread around the other.

Finishing, as a friend observed, is half science and half snake oil. Garrison hit upon the method most rodmakers use today. He dipped the rod, narrow end down, into an upright pipe filled with varnish, and pulled it out with a motor running at 1 rpm. This requires a pretty tall ceiling. I don’t have one, so I began to think about the last days of each semester in my college woodworking courses, when the shop smelled of Waterlox and Watco. It was the dustiest place on the planet, and yet because

we were using oil-based finishes that we wiped off, we could still get blemish-free finishes. So far, I’ve finished my rods with Birchwood Casey® TRU-OIL® Gun Stock Finish, a pure tung oil that is also traditional rod finish. I apply it with a rag, and rub it for about five minutes and set it aside to dry. If there are any imperfections, I sand them out gently with 1,000-grit paper. After three or four coats, the finish rivals varnish.

Finished, the guides will be tightly wrapped to the base of the rod with the silk thread.

If you start in the fall, and make no tomato stakes and start no fires, it will probably be early January by the time you apply the several coats of varnish that hold the silk thread in place. Around here, it will be a couple more weeks before the bluewinged olive hatch. See you on the stream.

Original article and pictures take http://www.rockler.com/how-to/making-bamboo-fly-fishing-rod/ site